Observer GigaStor Tech Specs : GigaStor Upgradeable 5U v3 : Technical Specifications : GigaStor Upgradeable 5U technical specifications
   
GigaStor Upgradeable 5U technical specifications
 
Page Contents
Supported QSFP/SFP/SFP+ media types
Created: 2013-03-13   Revised: 2015-07-23
 
The probe includes the Gen2 capture card and Expert Probe software. This allows for simultaneous connections by multiple users, and provides real-time expert processing at the probe. It also includes a number of security and reliability features.
Rack mounts and rail slide kits to mount the unit in a cabinet. Units may also be placed on a rack shelf or bench.
Do not remove the top panel from the probe. The probe was designed to cool most efficiently with the top panel in place. Opening the probe will void your warranty!
There is BIOS-controlled system monitoring that automatically slows down the CPU clocking in response to critical temperature sensors on the motherboard.
Figure 8: 5U Observer GigaStor Upgradeable
Feature
Description
A
Power button
Press this button to turn the unit on or off. When shutting the system down, wait about 10 seconds to allow the drives to stop before restarting.
B
System Reset Button
When pushed, the system resets.
C
USB Port
USB port for a USB device.
D
Operating System Drive
Removable hard drive with the operating system.
E
System Activity Lights
The blue Power light is on whenever the GigaStor unit is on.
The green Operating System light blinks whenever there is activity on the OS drive.
F
RAID drive locations
The RAID is built at the factory, and the drives are removed before being shipped to you. The locations indicate where each drive should be installed. Installing a drive in a location other than its preassigned slot may affect initial performance of your GigaStor while the RAID rebuilds itself.
Figure 9: 5U GigaStor Upgradeable
A
Redundant power supply
Two redundant power modules are standard.
B
Gen2 capture card
Slots for the Gen2 capture card or any other capture card. Your system will have one of:
1 Gb: 1, 2, 4, or 8 ports
10 Gb: 2, 4, or 8 ports
C
RAID card
Areca RAID card for the RAID 5 configuration.
D
Lights Out Management (LOM) port
LOM port, for out-of-band remote administration.
E
On-board video
For connecting a monitor or other display.
F
Ethernet ports
Ethernet (management) ports. By default, the right port is live and the left port is disabled. Passive probe instances should be pointed to this Ethernet connection so that the Gen2 capture card performs its best with the active probe instance.
Figure 10: GigaStor Upgradeable 5U dimensions
Table 1. System specifications
Feature
Description
Platform
19-inch rack-mountable probe appliance that supports up to 24 drives (in increments of 8 drives) and is available with storage capacities of 16 TB to 48 TB. GigaStor storage capacities can be upgraded in the field without removal of the system from the rack. Includes a redundant power supply and a field replaceable operating system drive.
RAM
64 GB RAM (32 for operating system, 32 for Observer Analyzer)
1 Gb Link Support
2, 4, or 6 Links (4, 8, and 12 ports)
10 Gb Link Support
1, 2, 4 or 6 Links (2, 4, 8, and 12 ports)
Additional Hardware
Includes network Observer nTAP(s) and media kit(s)
Key Remote Capabilities
Web-based management
Graceful power shutdown, start, and reboot
Pager and email alerts
Lights Out Capability
Manage, monitor and control the GigaStor remotely using an intuitive web-based interface via the IPMI (Intelligent Platform Management Interface) v1.5 / 2.0 with KVM support.
Dimensions
5U 19-inch rack-mountable appliance
16.84 in (W) x 8.72 in (H) x 26.08 in (mounting depth)
(Full probe depth with handles: 28.13 in)
42.23 cm (W) x 22.15 cm (H) x 66.23 cm (mounting depth) 
(Full probe depth with handles: 71.32 cm)
Weight
Fully populated with 24 drives
95 lbs (42.99 kg) / mounting rails: 9 lbs (4.1kg)
Power consumption (full load)
Input voltage: 100V-240V auto select 
Input frequency: 50/60Hz
GigaStor Upgradeable 549 W (1873 Btu/h)
10 Gb GigaStor Upgradeable 568 W (1938 Btu/h)
Operating Temperature
32 F (0 C) to 104 F (40 C)
 
Supported QSFP/SFP/SFP+ media types
Created: 2014-04-11   Revised: 2015-07-23
The Gen2 capture card requires SFP modules—a minimum of two per link. These are the supported media types.
 
40 Gb QSFP Transceivers
40GBASE-SR4
10 Gb Ethernet SFP+ Transceivers
10GBASE-SR
10GBASE-LR
10GBASE-ER
1 Gb Ethernet SFP Transceivers
1000BASE-SX
1000BASE-LX
1000BASE-TX
Note: XFP may only be used if your Gen2 capture card is a 2007 model.
If your Gen2 capture card is:
1 Gb, then only 1 Gb SFPs may be used. They can connect at 1000 Mb (1Gb) if optical, or 10/100/1000 Mb if copper.
10 Gb, then only 10 Gb SFP+ may be used. They only connect at 10 Gb and cannot be used with 40 Gb (multiplexed 10Gb).
40 Gb, then QSFP may be used and only if your exact Gen2 capture card model supports it.